Advanced stereo receiver featuring 20 watts per channel, min. RMS at 8 Ω from 40 Hz to 20,000 Hz with no more than 0,8% T.H.D.
Why pay for watts are wasted? The pioneer SX-535 combines practical power with advanced features and high performance to prove that high power is not always the answer when it comes to good high fidelity listening.. The FM tuner section employs a low-noise FET and a frequency-linear 3-gang variable capacitor in its front end to result in a high sensitivity of 1,9 µV (IHF). The FM IF stage uses a 5-stage limiter and phase-linear ceramic filters to boost FM station selectivity to 60 dB (IHF), capture ratio to 1,0 dB (IHF) and Signal-to-Noise Ratio to 70 dB. And to ensure stability under all operating conditions, the FM MPX circuit is the advanced PLL (Phase Lock Loop) type with an IC. Accurate high fidelity reproduction of all sounds is achieved by using a particularly precise phono equalizer in the Pioneer SX-535.. It keeps RIAA deviation within ±0,5 dB. As for versatility, the SX-535 has special circuits for two tape decks (deck 1 to deck 2 tape duplication is possible),, a dual meter tuning system with FM-linear dial scale and other control luxuries. And as for power, the SX-535 is ideal for use in the average-sized listening room with its continuous power output of 20 watts, per channel, min. RMS at 8 ohms from 40 Hz to 20,000 Hz with no more than 0,8% Total Harmonic Distortion. There are no wasted watts in the Pioneer SX-535 a stereo receiver value you shouldn't pass up.
Specifications
Amplifier Section
Continuous Power Output
from 20 Hz to 20 kHz (both channel driven)
20 W + 20 W at 8 Ω (rated power)
22 W + 22 W at 4 Ω
at 1 kHz (both channel driven):
22 W +22 W at 8 Ω
25 W + 25 W at 4 Ω
Total Harmonic Distortion
40 Hz - 20 kHz (Contiuous Power Output): less than 0,8%
1 W + 1 W, Power Output) : less than 0,08%
Intermodulation Distortion
Continuous Power Output : less than 0,8%
1 W + 1 W, Power Output : less than 0,08%
Power Bandwidth (IHF, Both channel driven): 10 Hz - 70 kHz (T.H.D. 0,8%)
Output Speaker: A; B; A + B, 4 Ω - 16 Ω
Headphone Output: 4 Ω - 16 Ω
Damping Factor (1 kHz, 8 Ω ): more than 30
Residual Hum and Noise (8 Ω , Pre & Power Amp.): less than 0,5 mV
Input Sensitivity/Impedance
Phono : 2,5 mV / 50 k Ω
Phono Overload Level (rms/p-p): 110 mV / 31 mV
Mic : 7 mV/ 85 k Ω
Aux : 150 mV/ 75 k Ω
Tape 1, 2 : 150 mV / 75 k Ω
Tape (DIN) : 150 mV/75 k Ω
Output Level/Impedance
Tape Rec 1, 2 : 150 mV
Tape Rec 2 (DIN) : 30 mV/80 k Ω
Frequency Response:
Phono (RIAA equalization): 30 Hz - 15 kHz ±0,5 dB
Aux, Tape : 20 Hz - 30 kHz ±1 dB
Tone Controls
Bass : =9 dB, -8 dB at 100 Hz
Treble : ±6 dB at 10 kHz
Loudness Contour (Vol. Control set at -490 dB position): +10 dB at 100 Hz; +5 dB at 10 kHz
Hum and Noise (IHF, short circuited, A network)
Phono : more than 70 dB
Mic : more than 65 dB
Aux, Tape : more than 90 dB
FM Section
Usable Sensitivity (IHF): 1,9 µV
Capture Ratio (IHF): 1,0 dB
Selectivity (IHF): 60 dB
Signal-to-Noise Ratio: 70 dB
Image Rejection (98 MHz): 60 dB
IF Rejection(98 MHz): 90 dB
Spurious Rejection: 75 dB
AM Suppression: 50 dB
Total Harmonic Distortion
Mono : less than 0,2%
Stereo : less than 0,4%
Frequency Response:
20 Hz - 15 kHz (+0,2 -2,0 dB)
50 Hz - 10 kHz (+0,2 -0,5 dB)
Stereo Separation
At 1 kHz : more than 40 dB
From 50 Hz to 10 kHz : more than 30 dB
Sub Carrier Suppression: 40 dB
Antenna Input: 300 Ω (balanced); 75 Ω (unbalanced)
Muting : On - off
AM Section
Sensitivity(IHF)
Ferrite Antenna ; 300 µV/m
Ext. Antenna : 15 µV
Selectivity: 35 dB
Signal-to-Noise Ratio : 50 dB
Image Rejection: 40 dB
iF Rejection: 70 dB
Miscellaneous
Semiconductors: 1 FET; 3 ICs; 29 Transistors; 15 Diodes
Power Requirements: AC 110, 120, 130, 220 and 240 V 50/60 Hz
Power Consumption: 130 W - 180 W
Dimensions (W x H x D): 480 x 147 x 405 mm (18-7/8" x 5-13/16" x 15-15/16")
Weight: 10,3 kg (22 lb 8 oz)
No comments:
Post a Comment