AM/FM Stereo Receiver
The KR-9600 Receiver puts independent power supplies behind each channel, so demanding musical passages in one channel won't cause distortion in the other. At 160 watts per channel minimum RMS power at 8 Ω , from 20 to 20,000 Hz, with no more than 0,08% Total Harmonic Distortion. The KR-9600 is the most powerful receiver we have ever made. What's more the KR-9600 is loaded with special features. A mid-range presence control, MIC mixing and source fading a deviation meter for source fading, a deviation meter for perfect off-air recording and 2 big power meters, to mention a few.
Kenwood's finest KR-9600 incredible power, advanced new circuitry and full complement of controls for unsurpassed performance. Features:
Dual power supplies end crosstalk distortion
Two selectable-range Power meters
Separate equalizer amplifiers for Phono 1 and Phono 2
FM front end couples a dual-gate MOS FET with 5-gang tuning capacitor for the theoretical limit in FM sensitivity (1,5 µV)
Low-distortion, 8-element linear phase IF filter
PLL in FM Multiplex for improved stereo separation
FM Dolby deemphasis switch
Dual function Signal/Deviation Meter
Microphone input for overdub on tape and Public Address
wo tape deck capability with bi-directional dubbing and tape-through circuit
Triple tone controls with Defeat switch
Optional CB-15 walnut veneer cabinet available
Specifications
FM Tuner Section
Usable Sensitivity: 8,7 dBf (1,5 µV)
50 dB Quieting Sensitivity:
Mono : 14,1 dBf (2,8 µV)
Stereo : 36,1 dBf (35 µV)
Signal-to-Noise Ratio
Mono : 75 dB
Stereo : 70 dB
Total Harmonic Distortion
Mono : 0,15%
Stereo : 0,2%
Frequency Response: 20 Hz to 15,000 Hz +0 dB, -1,5 dB
Capture ratio: 1,3 dB
Alternate Channel Selectivity: 83 dB
Spurious Response Ratio: 115 dB
Image Response Ratio: 100 dB
IF Response Ratio (Balanced): 115 dB
AM Suppression Ratio: 60 dB
Stereo Separation: 45 dB at 1,000 Hz ; 35 dB from 50 Hz to 10,000 Hz
Subcarrier Product Ratio: 65 dB
Antenna Impedance
Balanced : 300 Ω
Unbalanced : 75 Ω
AM Tuner Section
Usable Sensitivity: 10 µV
Signal-to-Noise Ratio: 50 dB
Image Rejection: 70 dB
Selectivity (IHF): 35 dB
IF Rejection: 75 dB
Power Amplifier Section
Power Output (20 to 20,000 Hz with no more than 0,08% T.H.D.):
160 W per channel minimum RMS at 8 Ω
200 W per channel minimum RMS at 4 Ω
Dynamic Power Output: 750 W (at 4 Ω )
Total Harmonic Distortion
0,08% at rated power into 8 Ω
0,05% at 1 W power into 8 Ω
Intermodulation Distortion (60 Hz : 7 kHz = 4 : 1)
0,08% at rated power into 8 Ω
0,05% at 1 W power into 8 Ω
Power Bandwidth: 5 Hz to 50,000 Hz
Damping Factor: 55 at 8 Ω
Input Sensitivity/Impedance: 1 V/50 k Ω
Speaker Impedance: 4 Ω to 16 Ω
Pre Amplifier Section
Input Sensitivity/Impedance
Phono 1 : 2,5 /50 k Ω
Phono 2 : 5,0 mV / 50 k Ω
Aux : 150 mV/50 k Ω
Tape : 150 mV/50 k Ω
Mic : 1,5 mV/50 k Ω
Signal-to-Noise Ratio
Phono 1 : 76 dB
Phono 2 : 80 dB
Aux : 95 dB
Tape : 95 dB
Mic : 65 dB
Maximum Input Level
Phono 1 : 500 mV (RMS) T.H.D. 0,08% at 1,000 Hz
Output Level/Impedance
Tape Rec Pin : 150 mV/100 Ω
Tape Rec DIN : 30 mV/80 k Ω
Pre Out : 1 V/5,3 k Ω
Frequency Response;
Phono 1 : RIAA standard curve +0,2 dB, -0,2 dB
Aux , Tape : 20 Hz to 40,000 Hz +0 dB, -1 dB
Mic : 100 Hz to 8 ,000 Hz +0 dB, -3 dB
Controls
Bass : ±10 dB at 100 Hz
Mid : ±10 dB at 800 Hz
Treble : ±8 dB at 10,000 Hz
Loudness Control (-30 dB): +3 dB at 100 Hz; +6 dB at 100 Hz
Low Filter : -9 dB at 100 Hz
High Filter : -9 dB at 10 kHz
General
Power Requirements: AC 110 - 120 V, 220 - 240 V, 50/60 Hz (switchable)
Power Consumption: 820 W at full power
AC Outlet: 1 Switched, 2 Unswitched
Dimensions (W x H x D): 580 x 169 x 420 mm (22-27/32" x 6-21/32" x 16-17/32")
Weight Net: 24 kg (52,9 lbs)
Nessun commento:
Posta un commento