A Powerful
Receiver of Tremendous power and Fidelity, Beautifully Packaged in the Most
Up-to Date Design.
The
SX-1500TD features highly advanced circuitry. An FET frong and ensures
extremely sensitive FM reception. There are four IC's in the IF section for
excellent selectivity, and a monolithic IC in the multiplex section for
improved separation. Silicon transistors ensure low-noise music power of a
tremendous 180 watts. In addition, a fine dynamic microphone comes with the
SX-1500TD for microphone mixing. You can connect up to three different stereo
loudspeaker systems. Uniquely attractive, with its silver and black contrast
and polished rosewood end-pieces.
Center
Channel Output
The
SX-1500TD has a center channel output on the rear panel, providing the
composite signal (L+R) for a 3-D (three-dimensional) system, when you connect
another amplifier to the center channel output.
In addition, stereo music can be recorded into a monophonic tape
recorder with this output which is controlled by the preamplifier section of
the SX-1500TD.
Phono Inputs
The
SX-1500TD has two sets of phono inputs, enabling you to compare cartridges.
Phono 1 is for magnetic and ceramic cartridges, and Phono 2 is for magnetic
cartridges.
AC Outlets
There are
three AC outlets for turntables and tape decks used with the receiver, a
switched AC outlet for 230 VA and two unswitched AC outlets for 230 VA.
Specifications
FM Section
Circuity: Front end using FET and 4-gang variable
capacitor, IF amplifier using 4 IC's
Frequency
Range: 87,5 to 108 MHz
IHF Usable
Sensitivity: 1,7 µV
Capture
Ratio: 0,7 dB 9at 98 MHz)
Image
Rejection: 72 dB (at 98 MHz)
Selectivity: 40 dB (IHF rating)
Signal-to-Noise
Ratio: 60 dB (IHF rating)
Antenna
Input: 300 Ω (balanced)
Multiplex
Section
Circuitry: Time-switching type demodulator using IC, FM
mono/stereo automatic selection
Channel
Separation: 38 dB (at 1 kHz)
AM Section
Circuitry: Superheterodyne
Frequency
Range: 525 to 1605 kHz
IHF Usable
Sensitivity: 18 µV
Image
Rejection: 77 dB (at 1,000 kHz)
Antenna
Input: Built-in ferrite loopstick
antenna
Audio
Section
Circuitry: Single-ended push-pull
Music Power
Output:
180
watts total at 4 Ω (IHF rating)
145
watts total at 8 Ω (IHF rating)
Continuous
Power Output (each channel driven):
70
watts / 70 watts at 4 Ω;
58
watts / 58 watts at 8 Ω
Harmonic
Distortion: less than 0,5% 9at 1 kHz
rated output)
Damping
Factor: 50 at 8 Ω (at 1 kHz)
Frequency
Response: 10 to 10,000 Hz ±2 dB
Power
Bandwidth: 15 to 40,000 Hz (Aux/IHF)
Hum and
Noise (at rated output):
Mag : better than 80 dB
Aux : better than 100 dB
Inputs
Sensitivit/Impedance (for rated output):
Magnetic
Phono : 3,3 mV/50 k Ω
Ceramic
Phono : 24 mV/100 k Ω
Microphone
: 3,2 mV/30 k Ω
Tape
Monitor : 200 mV/100 k Ω
Aux
: 200 mV/100 k Ω
Main
In : 480 mV/80 k Ω
Outputs
Terminals and Jacks:
Speaker
Impedance 4 to 8 Ω
Stereo
Headphone jack
Simultaneous
tape recording jacks, equipped with Tape Monitor switch
Tape
Recording/Playback jack (DIN standard)
Pre-amplifier
output jakcs
Center
channel output jack
Equalization
Curve: Phono RIAA
Tone
Controls (each channel):
Bass : boost 11 dB, out 16 dB at 50 Hz
Treble
: boost 10 dB, out 9 dB at 10 kHz
Filters:
Low : out 8 dB at 50 Hz
High : out 6 dB at 10 kHz
Loudness
Contour: Switchable to On-Off, boost 12
dB at 50 Hz, boost 9 dB at 10 kHz, with Volume control set at -40 dB
Power
Supply: 110, 117, 130, 220, 240 V
(switchable), 50/60 Hz, 250 VA, 230
watts max
Dimensions
(W x H x D): 459 x 145 x 369 mm
(18-1/16" x 5-11/15" x 14-1/2")
Weight: 11,4 kg (25 lbs 2 oz) net
No comments:
Post a Comment