If you are
looking for a beatutiful start in top-quality stereo, the Akai AM-2200 await
you. Perfectly matched in performance and styling, the formidable '2200
combination draws upon the latest advances in electronic audio technology to
offer you truly outstanding features previously available only with systems of
perhaps twice the price.
The AM-2200
boasts a solid 20W per channel continuous output over a wide span of 20 to
20,000 Hz that is versatilely managed by an exceptional array of console
controls. Both feature deluxe wood cabinets and push-button rear panel
connections. Perfectly paired for excellence in Quality and elegance in design,
the AM-2200 integrated amplifier combine
to form a stereo system of rare quality.
Power
Amplifier Section with Pure Complementary OCL Circuitry
The
AM-2200's two-stage differential pure complementary OCL circuitry assures
perfect stability over a wide frequency range and power bandwidth. This hefty
power amplifier provides 20 W per channel continuous output power, minimum RMS
at 8 ohms load impedance from 20 to 20,000 Hz with no more than 0,5% total
harmonic distortion.
Three-Stage
Equalizer with Wide Dynamic Range
A
three-stage direct-coupled negative feedback equalizer circuit linearizes phono
input signals to 110 mV (RMS 1 kHz). At the specified input of 3 mV, the
AM-2200 offers an extremely wide dynamic range of inputs.
Two Complete
Tape Systems
The Am-2200
has provisions for two complete stereo tape systems. Tape 1 and Tape 2
Record/Playback jacks enable single system operation or connection of two tape
decks for simultaneous recording. Dubbing from Tape 1 to Tape 2 Systems can
also be easily accomplished. The AM-2200 is also equipped with a Tape 1 DIN
jack.
Two Complete
Speaker Systems
Two speaker
systems can be driven by the AM-2200. its front panel speaker system selector
switches allow the use of either A or B systems independently or both systems
simultaneously.
Multiple
Sourece Inputs
The
versatile input selector lets you quickly change between Phono, Tuner and Aux
inputs. The Aux jack also be used for dubbing to Tape 1 and Tape 2 systems.
Tape
Monitoring and Headphones
The Tape
Monitor switches enable easy tape/source monitoring while a Phones jack for
stereo headphones permits private listening.
Precise Tone
Control and Loudness Switch
The AM-2200
features individual bass and Treble controls for precise low and high frequency
range adjustment. The Loudness switch boots bass and treble response for
perfectly balanced sound even at low volume.
High and Low
Filter Switches
His and Low
Filters eliminate undesired high and low frequency noises for beautifully
clearer audio reproduction.
Stereo
Balance Control
Perfect
left/right apeaker balance is easily attained to match room acoustics with the
convenient front panel stereo balance control
Large
Click-Type Volume Control
The
calibrated Volume control of the AM-2200 is especially large for easy
adjustment. It is operated with convenient click-stop settings from minimum to
maximum volume as handy points of reference.
Specifications
Power
Amplifier Section
Rated Output
Power (2-channels driven):
23
watts per channel at 4 Ω (minimum
RMS) from 20 to 20,000 Hz with no more
than 0,5% (THD)
20
watts per channel at 8 Ω (minimum
RMS) from 20 to 20,000 Hz with no more
than 0,5% (THD)
2 x 27
watts into 4 Ω at 1 kHz, with no more
than 0,5% THD
2 x 25
watts into 8 Ω at 1 kHz, with no more
than 0,5% THD
Power
Bandwidth (IHF): 10 Hz to 40 kHz/8 Ω (Total
Harmonic Distortion: 0.5%)
Signal-to-Noise
Ratio (IHF) ;
Phono: Better than 75 dB
Aux: Better than 95 dB
Residual
Noise: Less than 0.8 mV at 8 Ω
Channel
Separation (lHF) Phono: Better than 55
dB at 1,000 Hz
Damping
Factor: More than 60 (1 kHz, 8 Ω)
Output
Speakers: A, B (4 to 16 Ω)/A + B (8 to 16 ohms)
Output
Headphone: 4 to 16 Ω
Preamplifier
Section
Input
Sensitivity/Impedance;
Phono: 3 mV/47 k Ω
Aux: 150 mV/l00 k Ω
Tuner: 150 mV/100 k Ω
Tape Monitor (PIN/DIN): 150 mV at 100 k Ω / 30 mV
at 80 k Ω
Tape
Rec Output Level/Impedance (PIN/DIN):
150 mV at 100 k Ω / 30 mV at
100 k Ω
Frequency
Response
Phono (RIAA
Standard): 30 Hz to 15 kHz +1 dB, -1 dB
Tuner, Aux,
Tape Monitor: 10 Hz to 40 kHz
+0 dB, -1 dB
Tone
Control;
Bass: ±9 dB at 100 Hz
Treble: ±7 dB at 10 kHz
Loudness
Control: +10 dB at 100 Hz, +5 dB at 10
kHz (Volume control set at -30 dB position)
Filters
[Hgh/Low]: -6 dB at 10 kHz / -6 dB at 50
Hz
Miscellaneous
Semiconductors: Transistors -18, Diodes - 5,
IC's - 1
Power
Requirements: 110/220/240V , 50/60 Hz
Dimensions
(W x H x D): 380 x 125 x 263 mm, (15 x
4,9 x 10,3 inches)
Weight: 5.5 kg,
(12.1 lbs)
Nessun commento:
Posta un commento