What is stereo?




There are now two system of high fidelity, monophonic (monaural) and stereophonic. Monophonic is a system that starts from one microphone and is fed through a single high fidelity set. Stereophonic is a double system. Two separate microphones are placed at different sides of the orchestra and two different systems are used to keep the two signals or channels separated. Two separate speakers are used, placed on different sides of you room. Stereo is much like 3-D photography, two slightly different sound reach your ears giving you a new dimension in sound.




H.H. Scott '59





Akai AA-1020 receiver

The Akai AA-1020 

Promises a minimum power output of 20 watts per channel RMS at 8 ohms from 20 Hz to 20 khzs with no more than 0,4% total harmonic distortion. IHF tuner sensitivity is 2,0 µV.

The Multiplex Section features a Phase-Lock-Lop circuit which locks the 19 kHz FM sugnal phase to the phase of the 38 kHz switching signal for complete stability. Separation is better than 40 dB. An FM Muting switch cuts out noise during FM reception.

There's a power transistor protection unit which is activated if there's a short caused by a wrong speaker connection or when input goes over the top. The tone control circuit is a 2-stage direct coupled negative feedback type. It gives you precise tone adjustment of both channels Special "click: type Bass and Treble controls can be adjusted to plus or minus 10 dB. Each calibrated "click" represents 2 decibels. A two stage direct coupled negative feedback phono equalizer circuit provides a really wide dynamic range from disc.

The loudness switch boosts bass and treble response for balanced sound at low volume. High and low filters reduce extreme high and low frequency output for clearer playback quality.

There's a comprehensive tape dubbing facility as well. You can connect two tape decks for simultaneous recording from a single source. Tape monitor 1 has parallel DIN and phone connections. You can also connect up two pairs of speakers. A Speaker Selector gives you the choice of using the speakers individually or both together.

The AA-1020 has both FM and AM antenna terminals and a distance/local switch plus an AM Bar antenna for perfect station pick-up.

Versatility goes still further with two sets of phono jacks for connecting two magnetic cartridge turntables. Aux jacks will take ceramic and crystal cartridge turntables. And the Aux jacks can also be used for dubbing from an additional tape recorder to Tape 1 or Tape 2.

 


Specifications

Amplifier Section

Continuous Power Output (both channels driven):  20 W per channel RMS at 8  from 20 - 20,000 Hz

Total Harmonic Distortion:  less than 0,4%

Power bandwidth (IHF):  10 to 60,000 Hz

Input Sensitivity/Impedance: 

Phono 1, 2 :  3 mV/50 k  

Aux :  150 mV/80 k

Tape 1, 2 :  150 mV/80 k  

Signal-to-Noise Ratio (IHF)

Phono :  better than 80 dB

Tone Controls

Bass :  ±10 dB at 100 Hz

Treble :  ±10 dB at 10 kHz

Phono Equaliser:  RIAA ±1 dB

Loudness Control (volume at -30 dB):  100 Hz (+10 dB) / 10 kHz (+6 dB)

Filters

High :  -9 dB at 10 kHz

Low :  -6 dB at 50 Hz

FM Tuner Section

Frequency Range:  88 MHz to 108 MHz

Sensitivity (IHF):  2,0 µV

Capture Ratio (IHF):  2,0 dB

Selectivity (IHF):  better than 70 dB

Signal-to-Noise Ratio :  better than 68 dB

Image Rejection:  better than 65 dB

IF Rejection:  better than 90 dB

T.H.D. Stereo :  less than 0,5%

AM Tuner Section

Frequency Range:  535 kHz to 1608 kHz

Sensitivity (IHF):  200 µV (bar antenna); 5 µV (ext. Antenna)

Selectivity (IHF):  better than 30 dB at 1,000 kHz

AM Distortion:  less than 0,8%

Signal-to-Noise Ratio :  better than 50 dB

Dimensions (W x H x D):  440 x 140 x 350 mm (17,3" x 5,5" x 13,8")

Weight:  12 kg (26,4 lbs)

Nessun commento:

Posta un commento